<div dir="ltr">🍾<br></div><div class="gmail_extra"><br><div class="gmail_quote">On Thu, Aug 31, 2017 at 2:45 PM, Robert Nickerson <span dir="ltr"><<a href="mailto:rob@omsoft.com" target="_blank">rob@omsoft.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div text="#000000" bgcolor="#FFFFFF">
<p>HooraY!</p>
<p>RAN<br>
</p><div><div class="h5">
<br>
<div class="m_-4537296027655762070moz-cite-prefix">On 8/30/2017 9:38 PM, Roland
Synnestvedt wrote:<br>
</div>
<blockquote type="cite">
<div dir="auto">( that is supposed to be a 10mm x 10mm cube btw)</div>
<div class="gmail_extra"><br>
<div class="gmail_quote">On Aug 30, 2017 9:12 PM, "Roland
Synnestvedt" <<a href="mailto:rsynnest@gmail.com" target="_blank">rsynnest@gmail.com</a>> wrote:<br type="attribution">
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div dir="auto">Hi Rob,
<div dir="auto"><br>
</div>
<div dir="auto">I'm not sure if you already figured out
the firmware etc but I was able to print today! I'm
using the Repetier-Host AppImage and the Prusa fork of
Slic3r Appimage (AppImage is the recommended runtime for
both programs). I can do a write-up later this week but
the executables are located in ~/home/threed/AppImages
and can be run via command line or double click (they
are also in the system menu but so is the old repetier
installation which I think is bad), run them without
sudo (sudo can be problematic for graphical programs).</div>
<div dir="auto">The config is called "roland prusa i3",
250000 baud appears to be working. The printer does need
a new bed (a simple wood block), the mdf is falling
apart and uneven so I had to wedge some paper under it
to get the z axis right. It definitely still needs some
tweaking, but behold the almighty glory of the
futuristic technology now in our posession!! (attached)</div>
<div dir="auto"><br>
</div>
<div dir="auto">-Roland</div>
<br>
<div class="gmail_extra" dir="auto"><br>
<div class="gmail_quote">On Aug 28, 2017 8:37 PM,
"Robert Nickerson" <<a href="mailto:rob@omsoft.com" target="_blank">rob@omsoft.com</a>>
wrote:<br type="attribution">
<blockquote class="m_-4537296027655762070m_-1338265211978002859m_3634546899293753111quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Hi<br>
<br>
<br>
I think we have the printer at 250000 baud but mono
on linux wont go over 115200 baud<br>
<br>
<br>
<a href="https://github.com/repetier/Repetier-Host/issues/156" rel="noreferrer" target="_blank">https://github.com/repetier/Re<wbr>petier-Host/issues/156</a><br>
<br>
<br>
I tried to get the new marlin firmware uploaded with
the lower baud rate buit tried to verify the sketch
and it wouldnt verify, or I guess there is a mono
patch to allow other baud rates.<br>
<br>
<br>
Not so much luck and too hot by the printer.<br>
<br>
Close !<font color="#888888"><br>
<br>
<br>
-- <br>
Robert Nickerson<br>
UCD Class of 1996<br>
CEO, Om Networks<br>
<br>
cell: <a href="tel:5308483865" value="+15308483865" target="_blank">5308483865</a><br>
<a href="http://www.omsoft.com" rel="noreferrer" target="_blank">www.omsoft.com</a><br>
<br>
______________________________<wbr>_________________<br>
Davis Makerspace Discuss mailing list<br>
<a href="mailto:Discuss@lists.davismakerspace.org" target="_blank">Discuss@lists.davismakerspace.<wbr>org</a><br>
<a href="http://lists.davismakerspace.org/listinfo/discuss" rel="noreferrer" target="_blank">http://lists.davismakerspace.o<wbr>rg/listinfo/discuss</a><br>
</font></blockquote>
</div>
<br>
</div>
</div>
</blockquote>
</div>
</div>
<br>
<fieldset class="m_-4537296027655762070mimeAttachmentHeader"></fieldset>
<br>
<pre>______________________________<wbr>_________________
Davis Makerspace Discuss mailing list
<a class="m_-4537296027655762070moz-txt-link-abbreviated" href="mailto:Discuss@lists.davismakerspace.org" target="_blank">Discuss@lists.davismakerspace.<wbr>org</a>
<a class="m_-4537296027655762070moz-txt-link-freetext" href="http://lists.davismakerspace.org/listinfo/discuss" target="_blank">http://lists.davismakerspace.<wbr>org/listinfo/discuss</a>
</pre>
</blockquote>
<br>
<pre class="m_-4537296027655762070moz-signature" cols="72">--
Robert Nickerson
UCD Class of 1996
CEO, Om Networks
cell: <a href="tel:(530)%20848-3865" value="+15308483865" target="_blank">5308483865</a>
<a class="m_-4537296027655762070moz-txt-link-abbreviated" href="http://www.omsoft.com" target="_blank">www.omsoft.com</a>
</pre>
</div></div></div>
<br>______________________________<wbr>_________________<br>
Davis Makerspace Discuss mailing list<br>
<a href="mailto:Discuss@lists.davismakerspace.org">Discuss@lists.davismakerspace.<wbr>org</a><br>
<a href="http://lists.davismakerspace.org/listinfo/discuss" rel="noreferrer" target="_blank">http://lists.davismakerspace.<wbr>org/listinfo/discuss</a><br>
<br></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature" data-smartmail="gmail_signature">__________________________________<br>Emily Schleiner<br><a href="http://cordial-emily.com" target="_blank">cordial-emily.com</a><br></div>
</div>