<div dir="auto">( that is supposed to be a 10mm x 10mm cube btw)</div><div class="gmail_extra"><br><div class="gmail_quote">On Aug 30, 2017 9:12 PM, "Roland Synnestvedt" <<a href="mailto:rsynnest@gmail.com">rsynnest@gmail.com</a>> wrote:<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="auto">Hi Rob,<div dir="auto"><br></div><div dir="auto">I'm not sure if you already figured out the firmware etc but I was able to print today! I'm using the Repetier-Host AppImage and the Prusa fork of Slic3r Appimage (AppImage is the recommended runtime for both programs). I can do a write-up later this week but the executables are located in ~/home/threed/AppImages and can be run via command line or double click (they are also in the system menu but so is the old repetier installation which I think is bad), run them without sudo (sudo can be problematic for graphical programs).</div><div dir="auto">The config is called "roland prusa i3", 250000 baud appears to be working. The printer does need a new bed (a simple wood block),  the mdf is falling apart and uneven so I had to wedge some paper under it to get the z axis right. It definitely still needs some tweaking, but behold the almighty glory of the futuristic technology now in our posession!! (attached)</div><div dir="auto"><br></div><div dir="auto">-Roland</div><br><div class="gmail_extra" dir="auto"><br><div class="gmail_quote">On Aug 28, 2017 8:37 PM, "Robert Nickerson" <<a href="mailto:rob@omsoft.com" target="_blank">rob@omsoft.com</a>> wrote:<br type="attribution"><blockquote class="m_-1338265211978002859m_3634546899293753111quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Hi<br>
<br>
<br>
I think we have the printer at 250000 baud but mono on linux wont go over 115200 baud<br>
<br>
<br>
<a href="https://github.com/repetier/Repetier-Host/issues/156" rel="noreferrer" target="_blank">https://github.com/repetier/Re<wbr>petier-Host/issues/156</a><br>
<br>
<br>
I tried to get the new marlin firmware uploaded with the lower baud rate buit tried to verify the sketch and it wouldnt verify, or I guess there is a mono patch to allow other baud rates.<br>
<br>
<br>
Not so much luck and too hot by the printer.<br>
<br>
Close !<font color="#888888"><br>
<br>
<br>
-- <br>
Robert Nickerson<br>
UCD Class of 1996<br>
CEO, Om Networks<br>
<br>
cell: <a href="tel:5308483865" value="+15308483865" target="_blank">5308483865</a><br>
<a href="http://www.omsoft.com" rel="noreferrer" target="_blank">www.omsoft.com</a><br>
<br>
______________________________<wbr>_________________<br>
Davis Makerspace Discuss mailing list<br>
<a href="mailto:Discuss@lists.davismakerspace.org" target="_blank">Discuss@lists.davismakerspace.<wbr>org</a><br>
<a href="http://lists.davismakerspace.org/listinfo/discuss" rel="noreferrer" target="_blank">http://lists.davismakerspace.o<wbr>rg/listinfo/discuss</a><br>
</font></blockquote></div><br></div></div>
</blockquote></div></div>